In what cases and how is the Samsung washing machine flap cuff replaced correctly?

The sealing collar on the door of the front-loading Samsung washing machines is a very important detail.

It ensures a tight seal during the wash process, preventing water from leaking out through the door.

We will tell you how to replace the sunroof cuff of a Samsung washing machine in the article.

When should you change?

That the cuff needs to be replaced, can be identified by the following features:

• the wear of the rubber is visually visible - the presence of cracks, loosening of the edge, the appearance of roughness and irregularities on the rim, etc.;
• water leaks from the hatch during washing.

The cuff must be changed as soon as one of the above signs is noticed. Ignoring these circumstances can lead to more serious unpleasant consequences.

Training

Preliminary work on replacing the cuff includes two types of work: preparing the necessary tools (screwdrivers, rags, etc.) and the washing machine itself.

Before commencing repair work to replace the cuff, it is necessary:

• disconnect the washing machine from the mains by pulling out the plug from the socket;
• shut off the water supply;
• free the drum from things;
• drain the remaining water through the filter, access to which is located on the front panel at the bottom;
• pull out the cuvette for pouring the washing powder;
• extend the machine so that there is easy access to both the rear and the front.

How to remove and exchange?

In order to replace the seal on the hatch, you will have to partially disassemble the washing machine. This will require tools.

Step-by-step withdrawal procedure cuffs:

1. From the side of the back wall of the washing machine, in its upper part, unscrew the self-tapping screws that hold the top panel.
2. Standing behind the washing machine, pull the top cover towards you and remove.
3. Go to the front side of the machine.
4. In the upper part, near the powder receptacle, unscrew the screws that hold the panel with indicators and buttons.
5. Inspect the end faces at the top. In some models, the fastening of this horizontal panel may differ in the number and location of the screws.
6. Slide this panel towards you.This must be done very carefully so as not to break the contacts or cut the wires coming from the control module, which is located directly behind the panel.
7. It is advisable to disconnect the contacts (terminals) so that you can safely remove the control unit and remove it. If the wiring allows, then the panel can be placed on top of the machine without disconnecting.
8. In order to free the outer part of the cuff, it is necessary to find a wire attachment under the elastic band, which goes around the entire circumference and fixes the rubber. In the lower part there is a spring insert.
9. Pry the wire with a screwdriver and remove it, freeing it from under the rubber.
10. Separate the free edge of the cuff from the outer part of the machine body around the entire perimeter and bend it inside the drum so that it does not interfere.
11. Unscrew all screws holding the front side of the washing machine. There may be a different number of them depending on the model.
12. Remove the front panel.
13. Unscrew the collar holding the cuff.
14. Remove the cuff completely.
15. Clean all joints and areas that were under the rubber. This can be done using detergent and a brush or sponge.

Procedure for installing a new cuffs:

1. Put on a new cuff immediately together with the clamp, and carefully fill in.
2. Check that the retaining inner ring that holds the cuff is tucked into the groove on all sides.
3. Tighten the locking screw as far as it will go.
4. Install the outer facade panel. Secure with screws.
5. Install the outer part of the elastic, leading to the front panel.
6. Install the outer wire tie.
7. Carry out the assembly process further, checking how the parsing was carried out.

To facilitate assembly, you can take photographs at the stage of disassembling the machine. It is better to put all the self-tapping screws and clamps removed in order, so that later nothing is confused.

After finishing work on replacing the seal, it is necessary to carry out a test washwhile monitoring the condition of the cuff.

Video to help for a detailed acquaintance with the process of replacing the hatch cuff:

Master's call and the price of work

Repairing a machine to replace the sunroof cuff is a relatively simple process, but it requires accuracy and skill in handling equipment. If there is no such knowledge and skills, then it is better to call a master from a washing household appliance service company.

When calling a repair specialist, you must describe the problemand also tell you if there is a new cuff that needs to be installed. At a convenient time for the client, the master will come to the house and carry out repair work.

In order to be confident in the quality of the repair being carried out, it is advisable to call the master from a specialized company that has a permit to perform work. You can find such a company via the Internet by entering your city in the search.

The cost will include the labor and the price of a new cuff if the master brings his own.

Fees may vary by region, city and company. Only the work will cost from 1,000 rubles.

If the master uses his consumables or carries out additional work to repair other units, the cost will be higher.

A private master, unlike a representative of a self-respecting company, does not provide an official guarantee and is not responsible for the quality of the repair. In addition, there is a possibility of getting caught by scammers who can remove parts, take money to buy new ones and simply disappear.

Prevention measures

In order to avoid problems associated with the sunroof collar, the following expert advice should be taken into account:

1. When putting things in the drum, it is necessary to ensure that no sharp objects that can damage the washing machine, including the sealing rubber, get there.
2. Do not allow stagnation of water in the recess of the sealing lip, foreign objects in it.
3. When caring for the washing machine, in the process of cleaning the rubber rim, do not use objects with an abrasive surface, as well as scratch, scrape the cuff, and use force when cleaning it.
4. When putting things into the drum of the washing machine, you do not need to ram them, overload them by weight, or force oversized items to be pushed in.
5. After loading items in the drum, the door should close without effort. Things should not hang, lie on rubber, fall into the lock groove, etc.
6. Protect rubber parts from pets that might chew on them

Conclusion

You can replace the cuff of the washing machine yourself if you have the appropriate skills and a set of screwdrivers or by contacting the services of a master. At the same time, it is important that the part being replaced is identical and fully fits the parameters of the Samsung washing machine.